EVOBOND 502
SUPER GLUE

Identify the plastic type and both joining surfaces before choosing the adhesive. The manufacturer's technical sheet lists plastics as an application, but does not establish suitability for every plastic or coating. Clean the surfaces and remove grease. For PE, PP and ABS, the sheet specifies EVOBOND Primer AP-1 before the adhesive. Follow the primer's own instructions and test the actual parts before production.

Identify the rubber grade first. The technical data sheet lists rubber as an application and specifically calls for EVOBOND Primer AP-1 before the adhesive for silicone rubber, TPR and EPDM. Clean and degrease the joining surfaces, follow the primer instructions and test the joint. The sheet does not confirm the durability of every joint under repeated flexing, stretching or exposure to water.

Metal is a listed EVOBOND 502 application. The joining surfaces should be clean and completely free of grease. Check whether you are bonding bare metal or a coating and test the actual surface. The sheet lists a gap-filling value of 0.04 mm, so check the joint fit rather than assuming the adhesive will fill a wide gap. Published steel-to-steel test values do not prove the same strength for aluminium, other metals or coated parts.

Renovatio reports aluminium as a bonding application for its supplied product. The manufacturer's technical sheet lists metal in general but provides strength data for steel-to-steel joints, not aluminium. Identify whether the aluminium is bare, anodised, painted or otherwise coated. Clean and degrease the joining surfaces, check the joint fit and test the actual parts under the intended conditions before relying on the bond.

Wood appears in the manufacturer's setting-time table. However, EVOBOND 502 is a very low-viscosity adhesive, listed at 1.5–5.0 cP at 25 °C. The sheet recommends a higher-viscosity grade for more porous surfaces. Clean the joining surfaces and assess porosity and fit before a sample test. The supplied sheet does not establish approval for structural timber joints or load-bearing ladder repairs.

Do not assume that EVOBOND 502 alone is suitable. The manufacturer specifically lists PE, PP and ABS among difficult-to-bond materials and directs users to apply EVOBOND Primer AP-1 first, followed by the adhesive. Request the primer's instructions and confirm suitability on the exact plastic grade. No primer drying time or application quantity is specified in the supplied technical data sheet.

Identify both materials, any coatings, the joint gap and the conditions in use. Separate references to metal and plastic in a technical sheet do not establish performance for every metal-to-plastic combination. Ask Renovatio for documentation relevant to your combination, then test representative parts before production. Allow for the manufacturer's listed full cure time when assessing the result.

Renovatio reports glass as a bonding application for its supplied product. The supplied technical data sheet does not provide glass-specific strength or durability data. Identify the other joining material and any surface coating, clean and degrease the joining surfaces, then test on a sample before use. Ask for manufacturer confirmation for prolonged water exposure, temperature changes or safety-critical glazing; this guide does not establish suitability for those uses.

The technical data sheet reports 10–40 seconds for plastic, rubber, metal and wood at 22 °C and 50% relative humidity, at a tensile shear strength of 0.1 N/mm². It lists full cure as 24 hours. Initial setting is not full strength. Actual results depend on the materials, gap and conditions; test before placing the joint in service.

Read the product label and current safety data sheet before use. Work in a well-ventilated place, avoid breathing vapour and prevent contact with eyes, skin and clothing. Cyanoacrylate bonds skin in seconds and can generate strong heat. Follow the current product-specific safety data sheet for eye protection and suitable protective gloves. Do not use cotton, wool or paper materials when handling cyanoacrylate; contact can generate heat.

For a bonding enquiry, tell us both materials and their exact grades if known, surface coatings, joint gap, intended use, temperature and moisture exposure. Photos of the parts can help describe the application. For an EVOBOND 502 wholesale quotation, include the quantity and delivery country. Request the technical and safety data sheets; suitability, availability and delivery terms require individual confirmation.